Generation   Home

General • Periodic Maintenance Services • V-Belt • Replacement 2013 Subaru Forester

generation: → 2011 - 2016Release year → 2013 ✔ engine size → 2.5L ✔      add to compare      read later

PERIODIC MAINTENANCE SERVICES > V-belt

REPLACEMENT

1. NON-TURBO MODEL

1. Remove the V-belt covers.

2. Remove the air intake duct (Rear). INTAKE (INDUCTION)(H4DO) > Air Intake Duct > REMOVAL

3. Install the tool to belt tension adjuster assembly installation bolt.

4. Rotate the tool clockwise and loosen the V-belt to remove.

2013 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

5. Install in the reverse order of removal.

CAUTION:

• Be sure the V-belt is free from oil, grease and coolant.

• Wipe off any dust, oil or water on the groove of each pulley with cloth.

Tightening torque:

V-belt cover

13 N·m (1.3 kgf-m, 1.6 ft-lb)

2. TURBO MODEL

• Front side belt (for power steering oil pump and generator)

CAUTION:

• Do not use the front side belt if there is any oil, grease or coolant on the belt.

• Be careful not to rub the belt end surface with bare hands; exposed core may cause injury.

1. Remove the collector cover.

2. Remove the air intake duct (Rear). INTAKE (INDUCTION)(H4DOTC) > Air Intake Duct > REMOVAL

3. Remove the collector cover bracket.

2013 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

4. Loosen the bolt (A).

5. Loosen the slider bolt (B).

6. Remove the front side belt (C).

2013 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

7. Install the front side belt (C), and adjust the slider bolt (B) so as to obtain the specified belt tension. MECHANICAL(H4DOTC) > V-belt > INSPECTION

8. Tighten the bolt (A).

9. Tighten the slider bolt (B).

Tightening torque:

Bolt (A)

25 N·m (2.5 kgf-m, 18.4 ft-lb)

Slider bolt (B)

8 N·m (0.8 kgf-m, 5.9 ft-lb)

2013 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

10. Install the collector cover bracket.

Tightening torque:

T1: 8.5 N·m (0.9 kgf-m, 6.3 ft-lb)

T2: 25 N·m (2.5 kgf-m, 18.4 ft-lb)

2013 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

11. Install the air intake duct (rear). INTAKE (INDUCTION)(H4DOTC) > Air Intake Duct > INSTALLATION

12. Install the collector cover.

13. Start and run the engine for approximately five minutes to allow the V-belt to become fitted. (When using the gauge)

14. Stop the engine, check the belt tension and adjust as necessary. (When using the gauge)

15. Start and run the engine for approximately one minute to allow the V-belt to become fitted. (When using the gauge)

16. Stop the engine and check that the belt tension is within the specification. (When using the gauge)

17. Adjust until the specified belt tension is obtained. (When using the gauge)

• Rear side belt (for A/C)

CAUTION:

• Do not re-use the rear side belt.

• Be careful not to let oil, grease or coolant contact a new rear side belt.

• Be careful not to rub the belt end surface with bare hands; exposed core may cause injury.

• To install the rear side belt, always use the provided tools (belt stopper, belt guide, belt guide holder, and bolt).

1. Remove the front side belts.

2. Cut the rear side belt.

3. Install a new belt using an installation jig. MECHANICAL(H4DOTC) > V-belt > INSTALLATION

4. Install the front side belt.

MECHANICAL(H4DOTC) > V-belt > INSTALLATION

    2017-02-20 18:50:33    2017-05-11 10:18:46




I advise you to watch 2011 - 2016

© 2018. suforester.com
Order call back