Generation   Home

General • Periodic Maintenance Services • V-Belt • Replacement 2010 Subaru Forester

generation: → 2008 - 2010Release year → 2010 ✔ engine size → 2.5L ✔      add to compare      read later

PERIODIC MAINTENANCE SERVICES > V-belt

REPLACEMENT

1. FRONT SIDE BELT (FOR POWER STEERING OIL PUMP AND GENERATOR)

CAUTION:

• Do not use the front side belt if there is any oil, grease or coolant on the belt.

• Be careful not to rub the belt end surface with bare hands; exposed core may cause injury.

1. Remove the collector cover. (Turbo model)

2. Remove the V-belt covers. (Non-turbo model)

3. Remove the air intake duct (Rear). INTAKE (INDUCTION)(H4DOTC) > Air Intake Duct > REMOVAL

4. Remove the collector cover bracket. (Turbo model)

2010 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

5. Loosen the bolt (A).

6. Loosen the slider bolt (B).

7. Remove the front side belt (C).

2010 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

8. Install the front side belt (C), and adjust the slider bolt (B) so as to obtain the specified belt tension. MECHANICAL(H4DOTC) > V-belt > INSPECTION

9. Tighten the bolt (A).

10. Tighten the slider bolt (B).

Tightening torque:

Bolt (A)

25 N·m (2.5 kgf-m, 18.4 ft-lb)

Slider bolt (B)

8 N·m (0.8 kgf-m, 5.9 ft-lb)

2010 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

11. Install the collector cover bracket.

Tightening torque:

T1: 8.5 N·m (0.9 kgf-m, 6.3 ft-lb)

T2: 25 N·m (2.5 kgf-m, 18.4 ft-lb)

2010 Subaru Forester General • Periodic Maintenance Services • V-Belt • Replacement

12. Install the air intake duct (rear). INTAKE (INDUCTION)(H4DOTC) > Air Intake Duct > INSTALLATION

13. Install the collector cover. (Turbo model)

14. Install the V-belt cover. (Non-turbo model)

15. Start and run the engine for approximately five minutes to allow the V-belt to become fitted. (When using the gauge)

16. Stop the engine, check the belt tension and adjust as necessary. (When using the gauge)

17. Start and run the engine for approximately one minute to allow the V-belt to become fitted. (When using the gauge)

18. Stop the engine and check that the belt tension is within the specification. (When using the gauge)

19. Adjust until the specified belt tension is obtained. (When using the gauge)

2. REAR SIDE BELT (FOR AIR CONDITIONER)

CAUTION:

• Always use new rear side belt.

• Be careful that the new rear side belt does not come into contact with any oil, grease or coolant.

• Be careful not to rub the belt end surface with bare hands; exposed core may cause injury.

• When installing the rear side belt, always use the provided tools (belt stopper, belt guide, belt guide holder and bolt).

1. Remove the front side belts.

2. Cut the rear side belt.

3. Install a new belt using an installation jig. MECHANICAL(H4SO) > V-belt > INSTALLATION MECHANICAL(H4DOTC) > V-belt > INSTALLATION

4. Install the front side belt.

MECHANICAL(H4SO) > V-belt > INSTALLATION

    2017-02-20 18:50:33    2017-05-11 10:18:46




I advise you to watch 2008 - 2010

© 2018. suforester.com
Order call back